5.2 KiB
| layout | page_title | sidebar_current |
|---|---|---|
| intro | Run the Agent | gettingstarted-agent |
Run the Consul Agent
After Consul is installed, the agent must be run. The agent can either run in a server or client mode. Each datacenter must have at least one server, although 3 or 5 is recommended. A single server deployment is highly discouraged as data loss is inevitable in a failure scenario. This guide covers bootstrapping a new datacenter. All other agents run in client mode, which is a very lightweight process that registers services, runs health checks, and forwards queries to servers. The agent must be run for every node that will be part of the cluster.
Starting the Agent
For simplicity, we'll run a single Consul agent in server mode right now:
$ consul agent -server -bootstrap -data-dir /tmp/consul
==> WARNING: Bootstrap mode enabled! Do not enable unless necessary
==> WARNING: It is highly recommended to set GOMAXPROCS higher than 1
==> Starting Consul agent...
==> Starting Consul agent RPC...
==> Consul agent running!
Node name: 'Armons-MacBook-Air'
Datacenter: 'dc1'
Server: true (bootstrap: true)
Client Addr: 127.0.0.1 (HTTP: 8500, DNS: 8600, RPC: 8400)
Cluster Addr: 10.1.10.38 (LAN: 8301, WAN: 8302)
==> Log data will now stream in as it occurs:
[INFO] serf: EventMemberJoin: Armons-MacBook-Air.local 10.1.10.38
[INFO] raft: Node at 10.1.10.38:8300 [Follower] entering Follower state
[INFO] consul: adding server for datacenter: dc1, addr: 10.1.10.38:8300
[ERR] agent: failed to sync remote state: rpc error: No cluster leader
[WARN] raft: Heartbeat timeout reached, starting election
[INFO] raft: Node at 10.1.10.38:8300 [Candidate] entering Candidate state
[INFO] raft: Election won. Tally: 1
[INFO] raft: Node at 10.1.10.38:8300 [Leader] entering Leader state
[INFO] consul: cluster leadership acquired
[INFO] consul: New leader elected: Armons-MacBook-Air
[INFO] consul: member 'Armons-MacBook-Air' joined, marking health alive
As you can see, the Consul agent has started and has output some log data. From the log data, you can see that our agent is running in server mode, and has claimed leadership of the cluster. Additionally, the local member has been marked as a healthy member of the cluster.
-node flag.
Cluster Members
If you run consul members in another terminal, you can see the members of
the Consul cluster. You should only see one member (yourself). We'll cover
joining clusters in the next section.
$ consul members
Armons-MacBook-Air 10.1.10.38:8301 alive role=consul,dc=dc1,vsn=1,vsn_min=1,vsn_max=1,port=8300,bootstrap=1
The output shows our own node, the address it is running on, its
health state, and some metadata associated with the node. Some important
metadata keys to recognize are the role and dc keys. These tell you
the service name and the datacenter that member is within. These can be
used to lookup nodes and services using the DNS interface, which is covered
shortly.
The output from the members command is generated based on the
gossip protocol and is eventually consistent.
For a strongly consistent view of the world, use the
HTTP API, which forwards the request to the
Consul servers:
$ curl localhost:8500/v1/catalog/nodes
[{"Node":"Armons-MacBook-Air","Address":"10.1.10.38"}]
In addition to the HTTP API, the DNS interface can be used to query the node. Note that you have to make sure to point your DNS lookups to the Consul agent's DNS server, which runs on port 8600 by default. The format of the DNS entries (such as "Armons-MacBook-Air.node.consul") will be covered later.
$ dig @127.0.0.1 -p 8600 Armons-MacBook-Air.node.consul
...
;; QUESTION SECTION:
;Armons-MacBook-Air.node.consul. IN A
;; ANSWER SECTION:
Armons-MacBook-Air.node.consul. 0 IN A 10.1.10.38
Stopping the Agent
You can use Ctrl-C (the interrupt signal) to gracefully halt the agent.
After interrupting the agent, you should see it leave the cluster gracefully
and shut down.
By gracefully leaving, Consul notifies other cluster members that the node left. If you had forcibly killed the agent process, other members of the cluster would have detected that the node failed. When a member leaves, its services and checks are removed from the catalog. When a member fails, its health is simply marked as critical, but is not removed from the catalog. Consul will automatically try to reconnect to failed nodes, which allows it to recover from certain network conditions, while left nodes are no longer contacted.
Additionally, if an agent is operating as a server, a graceful leave is important to avoid causing a potential availability outage affecting the consensus protocol. See the guides section to safely add and remove servers.