23 KiB
| layout | page_title | sidebar_current |
|---|---|---|
| docs | HTTP API | docs-agent-http |
HTTP API
The main interface to Consul is a RESTful HTTP API. The API can be used for CRUD for nodes, services, and checks. The endpoints are versioned to enable changes without breaking backwards compatibility.
All endpoints fall into one of 4 categories:
- agent - Agent control
- catalog - Manages nodes and services
- health - Manages health checks
- status - Consul system status
Each of the categories and their respective endpoints are documented below.
Blocking Queries
Certain endpoints support a feature called a "blocking query". A blocking query is used to wait for a change to potentially take place using long polling.
Queries that support this will mention it specifically, however the use of this feature is the same for all. If supported, the query will set an HTTP header "X-Consul-Index". This is an opaque handle that the client will use.
To cause a query to block, the query parameters "?wait=60s&index=" are added to a request. The "?wait=" query parameter limits how long the query will potentially block for. It not set, it will default to 10 minutes. The "?index=" parameter is what was returned in a "X-Consul-Index" header.
When provided, Consul blocks sending a response until there is an update that could have cause the output to change, and thus advancing the index. A critical note is that when the query returns there is no guarantee of a change. It is possible that the timeout was reached, or that there was an idempotent write that does not affect the result.
Agent
The Agent endpoints are used to interact with a local Consul agent. Usually, services and checks are registered with an agent, which then takes on the burden of registering with the Catalog and performing anti-entropy to recover from outages. There are also various control APIs that can be used instead of the msgpack RPC protocol.
The following endpoints are supported:
- /v1/agent/checks: Returns the checks the local agent is managing
- /v1/agent/services : Returns the services local agent is managing
- /v1/agent/members : Returns the members as seen by the local serf agent
- /v1/agent/join/<address> : Trigger local agent to join a node
- /v1/agent/force-leave/<node>: Force remove node
- /v1/agent/check/register : Registers a new local check
- /v1/agent/check/deregister/<checkID> : Deregister a local check
- /v1/agent/check/pass/<checkID> : Mark a local test as passing
- /v1/agent/check/warn/<checkID> : Mark a local test as warning
- /v1/agent/check/fail/<checkID> : Mark a local test as critical
- /v1/agent/service/register : Registers a new local service
- /v1/agent/service/deregister/<serviceID> : Deregister a local service
/v1/agent/checks
This endpoint is used to return the all the checks that are registered with the local agent. These checks were either provided through configuration files, or added dynamically using the HTTP API. It is important to note that the checks known by the agent may be different than those reported by the Catalog. This is usually due to changes being made while there is no leader elected. The agent performs active anti-entropy, so in most situations everything will be in sync within a few seconds.
This endpoint is hit with a GET and returns a JSON body like this:
{
"service:redis":{
"Node":"foobar",
"CheckID":"service:redis",
"Name":"Service 'redis' check",
"Status":"passing",
"Notes":"",
"ServiceID":"redis",
"ServiceName":"redis"
}
}
/v1/agent/services
This endpoint is used to return the all the services that are registered with the local agent. These services were either provided through configuration files, or added dynamically using the HTTP API. It is important to note that the services known by the agent may be different than those reported by the Catalog. This is usually due to changes being made while there is no leader elected. The agent performs active anti-entropy, so in most situations everything will be in sync within a few seconds.
This endpoint is hit with a GET and returns a JSON body like this:
{
"redis":{
"ID":"redis",
"Service":"redis",
"Tag":"",
"Port":8000
}
}
/v1/agent/members
This endpoint is hit with a GET and returns the members the agent sees in the cluster gossip pool. Due to the nature of gossip, this is eventually consistent and the results may differ by agent. The strongly consistent view of nodes is instead provided by "/v1/catalog/nodes".
For agents running in server mode, providing a "?wan=1" query parameter returns the list of WAN members instead of the LAN members which is default.
This endpoint returns a JSON body like:
[
{
"Name":"foobar",
"Addr":"10.1.10.12",
"Port":8301,
"Tags":{
"bootstrap":"1",
"dc":"dc1",
"port":"8300",
"role":"consul"
},
"Status":1,
"ProtocolMin":1,
"ProtocolMax":2,
"ProtocolCur":2,
"DelegateMin":1,
"DelegateMax":3,
"DelegateCur":3
}
]
/v1/agent/join/<address>
This endpoint is hit with a GET and is used to instruct the agent to attempt to connect to a given address. For agents running in server mode, providing a "?wan=1" query parameter causes the agent to attempt to join using the WAN pool.
The endpoint returns 200 on successful join.
/v1/agent/force-leave/<node>
This endpoint is hit with a GET and is used to instructs the agent to force a node into the left state. If a node fails unexpectedly, then it will be in a "failed" state. Once in this state, Consul will attempt to reconnect, and additionally the services and checks belonging to that node will not be cleaned up. Forcing a node into the left state allows its old entries to be removed.
The endpoint always returns 200.
/v1/agent/check/register
The register endpoint is used to add a new check to the local agent. There is more documentation on checks here. Checks are either a script or TTL type. The agent is reponsible for managing the status of the check and keeping the Catalog in sync.
The register endpoint expects a JSON request body to be PUT. The request body must look like:
{
"ID": "mem",
"Name": "Memory utilization",
"Notes": "Ensure we don't oversubscribe memory",
"Script": "/usr/local/bin/check_mem.py",
"Interval": "10s",
"TTL": "15s"
}
The Name field is mandatory, as is either Script and Interval
or TTL. Only one of Script and Interval or TTL should be provided.
If an ID is not provided, it is set to Name. You cannot have duplicate
ID entries per agent, so it may be necessary to provide an ID. The Notes
field is not used by Consul, and is meant to be human readable.
If a Script is provided, the check type is a script, and Consul will
evaluate the script every Interval to update the status. If a TTL type
is used, then the TTL update APIs must be used to periodically update
the state of the check.
The return code is 200 on success.
/v1/agent/check/deregister/<checkId>
The deregister endpoint is used to remove a check from the local agent. The CheckID must be passed after the slash. The agent will take care of deregistering the check with the Catalog.
The return code is 200 on success.
/v1/agent/check/pass/<checkId>
This endpoint is used with a check that is of the TTL type. When this endpoint is accessed, the status of the check is set to "passing", and the TTL clock is reset.
The return code is 200 on success.
/v1/agent/check/warn/<checkId>
This endpoint is used with a check that is of the TTL type. When this endpoint is accessed, the status of the check is set to "warning", and the TTL clock is reset.
The return code is 200 on success.
/v1/agent/check/fail/<checkId>
This endpoint is used with a check that is of the TTL type. When this endpoint is accessed, the status of the check is set to "critical", and the TTL clock is reset.
The return code is 200 on success.
/v1/agent/service/register
The register endpoint is used to add a new service to the local agent. There is more documentation on services here. Services may also provide a health check. The agent is reponsible for managing the status of the check and keeping the Catalog in sync.
The register endpoint expects a JSON request body to be PUT. The request body must look like:
{
"ID": "redis1",
"Name": "redis",
"Tag": "master",
"Port": 8000,
"Check": {
"Script": "/usr/local/bin/check_redis.py",
"Interval": "10s",
"TTL": "15s"
}
}
The Name field is mandatory, If an ID is not provided, it is set to Name.
You cannot have duplicate ID entries per agent, so it may be necessary to provide an ID.
Tag, Port and Check are optional. If Check is provided, only one of Script and Interval
or TTL should be provided. There is more information about checks here.
The created check will be named "service:<ServiceId>".
The return code is 200 on success.
/v1/agent/service/deregister/<serviceId>
The deregister endpoint is used to remove a service from the local agent. The ServiceID must be passed after the slash. The agent will take care of deregistering the service with the Catalog. If there is an associated check, that is also deregistered.
The return code is 200 on success.
Catalog
The Catalog is the endpoint used to register and deregister nodes, services, and checks. It also provides a number of query endpoints.
The following endpoints are supported:
- /v1/catalog/register : Registers a new node, service, or check
- /v1/catalog/deregister : Deregisters a node, service, or check
- /v1/catalog/datacenters : Lists known datacenters
- /v1/catalog/nodes : Lists nodes in a given DC
- /v1/catalog/services : Lists services in a given DC
- /v1/catalog/service/<service> : Lists the nodes in a given service
- /v1/catalog/node/<node> : Lists the services provided by a node
The last 4 endpoints of the catalog support blocking queries.
/v1/catalog/register
The register endpoint is a low level mechanism for direclty registering or updating entries in the catalog. It is usually recommended to use the agent local endpoints, as they are simpler and perform anti-entropy.
The register endpoint expects a JSON request body to be PUT. The request body must look like:
{
"Datacenter": "dc1",
"Node": "foobar",
"Address": "192.168.10.10",
"Service": {
"ID": "redis1",
"Service": "redis",
"Tag": "master",
"Port": 8000,
},
"Check": {
"Node": "foobar",
"CheckID": "service:redis1",
"Name": "Redis health check",
"Notes": "Script based health check",
"Status": "passing",
"ServiceID": "redis1"
}
}
The behavior of the endpoint depends on what keys are provided. The endpoint
requires Node and Address to be provided, while Datacenter will be defaulted
to match that of the agent. If only those are provided, the endpoint will register
the node with the catalog.
If the Service key is provided, then the service will also be registered. If
ID is not provided, it will be defaulted to Service. It is mandated that the
ID be node-unique. Both Tag and Port can be omitted.
If the Check key is provided, then a health check will also be registered. It
is important to remember that this register API is very low level. This manipulates
the health check entry, but does not setup a script or TTL to actually update the
status. For that behavior, an agent local check should be setup.
The CheckID can be omitted, and will default to the Name. Like before, the
CheckID must be node-unique. The Notes is an opaque field that is meant to
hold human readable text. If a ServiceID is provided that matches the ID
of a service on that node, then the check is treated as a service level health
check, instead of a node level health check. Lastly, the status must be one of
"unknown", "passing", "warning", or "critical". The "unknown" status is used
to indicate that the initial check has not been performed yet.
It is important to note that Check does not have to be provided with Service
and visa-versa. They can be provided or omitted at will.
If the API call succeeds a 200 status code is returned.
/v1/catalog/deregister
The deregister endpoint is a low level mechanism for direclty removing entries in the catalog. It is usually recommended to use the agent local endpoints, as they are simpler and perform anti-entropy.
The deregister endpoint expects a JSON request body to be PUT. The request body must look like one of the following:
{
"Datacenter": "dc1",
"Node": "foobar",
}
{
"Datacenter": "dc1",
"Node": "foobar",
"CheckID": "service:redis1"
}
{
"Datacenter": "dc1",
"Node": "foobar",
"ServiceID": "redis1",
}
The behavior of the endpoint depends on what keys are provided. The endpoint
requires Node to be provided, while Datacenter will be defaulted
to match that of the agent. If only Node is provided, then the node, and
all associated services and checks are deleted. If CheckID is provided, only
that check belonging to the node is removed. If ServiceID is provided, then the
service along with it's associated health check (if any) is removed.
If the API call succeeds a 200 status code is returned.
/v1/catalog/datacenters
This endpoint is hit with a GET and is used to return all the datacenters that are known by the Consul server.
It returns a JSON body like this:
["dc1", "dc2"]
This endpoint does not require a cluster leader, and as such will succeed even during an availability outage. It can thus be a simple check to see if any Consul servers are routable.
/v1/catalog/nodes
This endpoint is hit with a GET and returns the nodes known about in a given DC. By default the datacenter of the agent is queried, however the dc can be provided using the "?dc=" query parameter.
It returns a JSON body like this:
[
{
"Node":"baz",
"Address":"10.1.10.11"
},
{
"Node":"foobar",
"Address":"10.1.10.12"
}
]
This endpoint supports blocking queries.
/v1/catalog/services
This endpoint is hit with a GET and returns the services known about in a given DC. By default the datacenter of the agent is queried, however the dc can be provided using the "?dc=" query parameter.
It returns a JSON body like this:
{
"consul":[""],
"redis":[""],
"postgresql":["master","slave"]
}
The main object keys are the service names, while the array provides all the known tags for a given service.
This endpoint supports blocking queries.
/v1/catalog/service/<service>
This endpoint is hit with a GET and returns the nodes providing a service in a given DC. By default the datacenter of the agent is queried, however the dc can be provided using the "?dc=" query parameter.
The service being queried must be provided after the slash. By default all nodes in that service are returned. However, the list can be filtered by tag using the "?tag=" query parameter.
It returns a JSON body like this:
[
{
"Node":"foobar",
"Address":"10.1.10.12",
"ServiceID":"redis",
"ServiceName":"redis",
"ServiceTag":"",
"ServicePort":8000
}
]
This endpoint supports blocking queries.
/v1/catalog/node/<node>
This endpoint is hit with a GET and returns the node provided services. By default the datacenter of the agent is queried, however the dc can be provided using the "?dc=" query parameter. The node being queried must be provided after the slash.
It returns a JSON body like this:
{
"Node":{
"Node":"foobar",
"Address":"10.1.10.12"
},
"Services":{
"consul":{
"ID":"consul",
"Service":"consul",
"Tag":"",
"Port":8300
},
"redis":{
"ID":"redis",
"Service":"redis",
"Tag":"",
"Port":8000
}
}
}
This endpoint supports blocking queries.
Health
The Health used to query health related information. It is provided seperately from the Catalog, since users may prefer to not use the health checking mechanisms as they are totally optional. Additionally, some of the query results from the Health system are filtered, while the Catalog endpoints provide the raw entries.
The following endpoints are supported:
- /v1/health/node/<node>: Returns the health info of a node
- /v1/health/checks/<service>: Returns the checks of a service
- /v1/health/service/<service>: Returns the nodes and health info of a service
- /v1/health/state/<state>: Returns the checks in a given state
All of the health endpoints supports blocking queries.
/v1/health/node/<node>
This endpoint is hit with a GET and returns the node specific checks known. By default the datacenter of the agent is queried, however the dc can be provided using the "?dc=" query parameter. The node being queried must be provided after the slash.
It returns a JSON body like this:
[
{
"Node":"foobar",
"CheckID":"serfHealth",
"Name":"Serf Health Status",
"Status":"passing",
"Notes":"",
"ServiceID":"",
"ServiceName":""
},
{
"Node":"foobar",
"CheckID":"service:redis",
"Name":"Service 'redis' check",
"Status":"passing",
"Notes":"",
"ServiceID":"redis",
"ServiceName":"redis"
}
]
In this case, we can see there is a system level check (no associated
ServiceID, as well as a service check for Redis). The "serfHealth" check
is special, in that all nodes automatically have this check. When a node
joins the Consul cluster, it is part of a distributed failure detection
provided by Serf. If a node fails, it is detected and the status is automatically
changed to "critical".
This endpoint supports blocking queries.
/v1/health/checks/<service>
This endpoint is hit with a GET and returns the checks associated with a service in a given datacenter. By default the datacenter of the agent is queried, however the dc can be provided using the "?dc=" query parameter. The service being queried must be provided after the slash.
It returns a JSON body like this:
[
{
"Node":"foobar",
"CheckID":"service:redis",
"Name":"Service 'redis' check",
"Status":"passing",
"Notes":"",
"ServiceID":"redis",
"ServiceName":"redis"
}
]
This endpoint supports blocking queries.
/v1/health/service/<service>
This endpoint is hit with a GET and returns the service nodes providing a given service in a given datacenter. By default the datacenter of the agent is queried, however the dc can be provided using the "?dc=" query parameter.
The service being queried must be provided after the slash. By default all nodes in that service are returned. However, the list can be filtered by tag using the "?tag=" query parameter.
This is very similar to the /v1/catalog/service endpoint however, this endpoint automatically returns the status of the associated health check, as well as any system level health checks. This allows a client to avoid sending traffic to nodes failing health tests, or who are reporting warnings.
Users can also built in support for dynamic load balancing and other features by incorporating the use of health checks.
It returns a JSON body like this:
[
{
"Node":{
"Node":"foobar",
"Address":"10.1.10.12"
},
"Service":{
"ID":"redis",
"Service":"redis",
"Tag":"",
"Port":8000
},
"Checks":[
{
"Node":"foobar",
"CheckID":"service:redis",
"Name":"Service 'redis' check",
"Status":"passing",
"Notes":"",
"ServiceID":"redis",
"ServiceName":"redis"
},{
"Node":"foobar",
"CheckID":"serfHealth",
"Name":"Serf Health Status",
"Status":"passing",
"Notes":"",
"ServiceID":"",
"ServiceName":""
}
]
}
]
This endpoint supports blocking queries.
/v1/health/state/<state>
This endpoint is hit with a GET and returns the checks in a specific state for a given datacenter. By default the datacenter of the agent is queried, however the dc can be provided using the "?dc=" query parameter.
The state being queried must be provided after the slash. The supported states are "unknown", "passing", "warning", or "critical".
It returns a JSON body like this:
[
{
"Node":"foobar",
"CheckID":"serfHealth",
"Name":"Serf Health Status",
"Status":"passing",
"Notes":"",
"ServiceID":"",
"ServiceName":""
},
{
"Node":"foobar",
"CheckID":"service:redis",
"Name":"Service 'redis' check",
"Status":"passing",
"Notes":"",
"ServiceID":"redis",
"ServiceName":"redis"
}
]
This endpoint supports blocking queries.
Status
The Status endpoints are used to get information about the status of the Consul cluster. This are generally very low level, and not really useful for clients.
The following endpoints are supported:
- /v1/status/leader : Returns the current Raft leader
- /v1/status/peers : Returns the current Raft peer set
/v1/status/leader
This endpoint is used to get the Raft leader for the datacenter the agent is running in. It returns only an address like:
"10.1.10.12:8300"
/v1/status/peers
This endpoint is used to get the Raft peers for the datacenter the agent is running in. It returns a list of addresses like:
["10.1.10.12:8300", "10.1.10.11:8300", "10.1.10.10:8300"]