* Ensure the mesh gateway configuration comes back in the api within each upstream
* Add a test for the MeshGatewayConfig in the ToAPI functions
* Ensure we don’t use gateways for dc local connections
* Update the svc kind index for deletions
* Replace the proxycfg.state cache with an interface for testing
Also start implementing proxycfg state testing.
* Update the state tests to verify some gateway watches for upstream-targets of a discovery chain.
Also:
- add back an internal http endpoint to dump a compiled discovery chain for debugging purposes
Before the CompiledDiscoveryChain.IsDefault() method would test:
- is this chain just one resolver step?
- is that resolver step just the default?
But what I forgot to test:
- is that resolver step for the same service that the chain represents?
This last point is important because if you configured just one config
entry:
kind = "service-resolver"
name = "web"
redirect {
service = "other"
}
and requested the chain for "web" you'd get back a **default** resolver
for "other". In the xDS code the IsDefault() method is used to
determine if this chain is "empty". If it is then we use the
pre-discovery-chain logic that just uses data embedded in the Upstream
object (and still lets the escape hatches function).
In the example above that means certain parts of the xDS code were going
to try referencing a cluster named "web..." despite the other parts of
the xDS code maintaining clusters named "other...".
Both 'consul config write' and server bootstrap config entries take a
decoding detour through mapstructure on the way from HCL to an actual
struct. They both may take in snake_case or CamelCase (for consistency)
so need very similar handling.
Unfortunately since they are operating on mirror universes of structs
(api.* vs structs.*) the code cannot be identitical, so try to share the
kind-configuration and duplicate the rest for now.
* Ensure we MapWalk the proxy config in the NodeService and ServiceNode structs
This gets rid of some json encoder errors in the catalog endpoints
* Allow passing explicit bind addresses to envoy
* Move map walking to the ConnectProxyConfig struct
Any place where this struct gets JSON encoded will benefit as opposed to having to implement it everywhere.
* Fail when a non-empty address is provided and not bindable
* camel case
* Update command/connect/envoy/envoy.go
Co-Authored-By: Paul Banks <banks@banksco.de>
* Retry the creation of the test server three times.
* Reduce the retry timeout for the API wait to 2 seconds, opting to fail faster and start over.
* Remove wait for leader from server creation. This wait can be added on a test by test basis now that the function is being exported.
* Remove wait for anti-entropy sync. This is built into the existing WaitForSerfCheck func, so that can be used if the anti-entropy wait is needed
Previously a sequence of events like:
Start
Stop
Start
Stop
would segfault on the second stop because the original ctx and cancel func were only initialized during the constructor and not during Start.
When the envoy healthy panic threshold was explicitly disabled as part
of L7 traffic management it changed how envoy decided to load balance to
endpoints in a cluster. This only matters when envoy is in "panic mode"
aka "when you have a bunch of unhealthy endpoints". Panic mode sends
traffic to unhealthy instances in certain circumstances.
Note: Prior to explicitly disabling the healthy panic threshold, the
default value is 50%.
What was happening is that the test harness was bringing up consul the
sidecars, and the service instances all at once and sometimes the
proxies wouldn't have time to be checked by consul to be labeled as
'passing' in the catalog before a round of EDS happened.
The xDS server in consul effectively queries /v1/health/connect/s2 and
gets 1 result, but that one result has a 'critical' check so the xDS
server sends back that endpoint labeled as UNHEALTHY.
Envoy sees that 100% of the endpoints in the cluster are unhealthy and
would enter panic mode and still send traffic to s2. This is why the
test suites PRIOR to disabling the healthy panic threshold worked. They
were _incorrectly_ passing.
When the healthy panic threshol is disabled, envoy never enters panic
mode in this situation and thus the cluster has zero healthy endpoints
so load balancing goes nowhere and the tests fail.
Why does this only affect the test suites for envoy 1.8.0? My guess is
that https://github.com/envoyproxy/envoy/pull/4442 was merged into the
1.9.x series and somehow that plays a role.
This PR modifies the bats scripts to explicitly wait until the upstream
sidecar is healthy as measured by /v1/health/connect/s2?passing BEFORE
trying to interrogate envoy which should make the tests less racy.
R.B. Boyer
Alvin Huang
Judith Malnick
Freddy
Sarah Adams
hashicorp-ci
Jack Pearkes
John Cowen
Matt Keeler