27ee0f0558
* Hugo init * Init Hugo book * Add basic README and title * Import RFC: 1/COSS * Move example content to dedicated folder * Basic menu * Tweak single layout * Fix base url and permalink * Basic index tweaks * Add netifly config * gitignore * 1/COSS: Add COSS lifecycle * Remove public artifact * Add basic numbers in menu * Empty READMEs init * Import mvds spec raw * 2/MVDS: Simplify * 3/REMOTE-LOG: Import * 3/REMOTE-LOG: Simplify * 4/MVDS-META: Import * 4/MVDS-META Simplify * Tweaks * 5/WAKU0: Import * 5: Simplify * 6/WAKU1: Import * 6/WAKU1: Simplify * 7/WAKU-DATA: Import * 7/WAKU-DATA: Simplify * 8/WAKU-MAIL: Import * 8/WAKU-MAIL: Simplify * Tweak * 9/WAKU-RPC: Import * 9/WAKU-RPC: Simplify * 10/WAKU2: Import * 10/WAKU2: Simplify * 11/WAKU-RELAY: Import * Tweaks * 11/WAKU-RELAY: Simplify * 12/WAKU-FILTER: Import * 12/WAKU2-FILTER: Simplify * 13/WAKU-STORE: Import * 13/WAKU-STORE: Simplify * 14/WAKU-MESSAGE: Import * 14/WAKU-MESSAGE: Simplify * 15/WAKU-BRIDGE: Import * 15: Simplify * 16: Import * 16: Simplify * 17: Import * 17: Simplify * 18: Import * 18: Simplify * 12: Bump update * 14: Bump update * 11: Bump update * 17: Bump update * 18: Bump update * 16: Bump update * Fix slug for 18 * Editor changes for 11, 12, 15 * Revert "Editor changes for 11, 12, 15" This reverts commit |
||
|---|---|---|
| .. | ||
| README.md | ||
README.md
| slug | title | name | status | editor |
|---|---|---|---|---|
| 15 | 15/WAKU-BRIDGE | Waku Bridge | raw | Hanno Cornelius <hanno@status.im> |
A bridge between Waku v1 and Waku v2.
Bridge
A bridge requires supporting both Waku versions:
- Waku v1 - using devp2p RLPx protocol
- Waku v2 - using libp2p protocols
Packets received on the Waku v1 network SHOULD be published just once on the Waku v2 network. More specifically, the bridge SHOULD publish this through the Waku Relay (PubSub domain).
Publishing such packet will require the creation of a new Message with a
new WakuMessage as data field. The data and topic field from the Waku v1
Envelope MUST be copied to the payload and contentTopic fields of the
WakuMessage. Other fields such as nonce, expiry and ttl will be dropped as
they become obsolete in Waku v2.
Before this is done, the usual envelope verification still applies:
- Expiry & future time verification
- PoW verification
- Size verification
Bridging SHOULD occur through the WakuRelay, but it MAY also be done on other Waku
v2 protocols (e.g. WakuFilter). The latter is however not advised as it will
increase the complexity of the bridge and because of the
Security Considerations explained further below.
Packets received on the Waku v2 network SHOULD be posted just once on the Waku
v1 network. The Waku v2 WakuMessage contains only the payload and
contentTopic fields. The bridge MUST create a new Waku v1 Envelope and
copy over the payload and contentFilter fields to the data and topic
fields. Next, before posting on the network, the bridge MUST set a new expiry
and ttl and do the PoW nonce calculation.
Security Considerations
As mentioned above, a bridge will be posting new Waku v1 envelopes, which requires doing the PoW nonce calculation.
This could be a DoS attack vector, as the PoW calculation will make it more expensive to post the message compared to the original publishing on the Waku v2 network. Low PoW setting will lower this problem, but it is likely that it is still more expensive.
For this reason, bridges SHOULD probably be run independently of other nodes, so that a bridge that gets overwhelmed does not disrupt regular Waku v2 to v2 traffic.
Bridging functionality SHOULD also be carefully implemented so that messages do not bounce back and forth between the two networks. The bridge SHOULD properly track messages with a seen filter so that no amplification can be achieved here.
Copyright
Copyright and related rights waived via CC0.