54/WAKU2-X3DH-SESSIONS #
Session management for Waku X3DH #
- Status: draft
- Editor: Aaryamann Challani aaryamann@status.im
- Contributors: Andrea Piana andreap@status.im , Pedro Pombeiro pedro@status.im , Corey Petty corey@status.im , Oskar Thorén oskar@status.im , Dean Eigenmann dean@status.im
Abstract #
This document specifies how to manage sessions based on an X3DH key exchange. This includes how to establish new sessions, how to re-establish them, how to maintain them, and how to close them.
53/WAKU2-X3DH specifies the Waku X3DH
protocol for end-to-end encryption.
Once two peers complete an X3DH handshake, they SHOULD establish an X3DH session.
Session Establishment #
A node identifies a peer by their installation-id
which MAY be interpreted as a device identifier.
Discovery of pre-key bundles #
The node’s pre-key bundle MUST be broadcast on a content topic derived from the node’s public key, so that the first message may be PFS-encrypted. Each peer MUST publish their pre-key bundle periodically to this topic, otherwise they risk not being able to perform key-exchanges with other peers. Each peer MAY publish to this topic when their metadata changes, so that the other peer can update their local record.
If peer A wants to send a message to peer B, it MUST derive the topic from peer B’s public key, which has been shared out of band. Partitioned topics have been used to balance privacy and efficiency of broadcasting pre-key bundles.
The number of partitions that MUST be used is 5000.
The topic MUST be derived as follows:
var partitionsNum *big.Int = big.NewInt(5000)
var partition *big.Int = big.NewInt(0).Mod(peerBPublicKey, partitionsNum)
partitionTopic := "contact-discovery-" + strconv.FormatInt(partition.Int64(), 10)
var hash []byte = keccak256(partitionTopic)
var topicLen int = 4
if len(hash) < topicLen {
topicLen = len(hash)
}
var contactCodeTopic [4]byte
for i = 0; i < topicLen; i++ {
contactCodeTopic[i] = hash[i]
}
Initialization #
A node initializes a new session once a successful X3DH exchange has taken place. Subsequent messages will use the established session until re-keying is necessary.
Negotiated topic to be used for the session #
After the peers have performed the initial key exchange, they MUST derive a topic from their shared secret to send messages on. To obtain this value, take the first four bytes of the keccak256 hash of the shared secret encoded in hexadecimal format.
sharedKey, err := ecies.ImportECDSA(myPrivateKey).GenerateShared(
ecies.ImportECDSAPublic(theirPublicKey),
16,
16,
)
hexEncodedKey := hex.EncodeToString(sharedKey)
var hash []byte = keccak256(hexEncodedKey)
var topicLen int = 4
if len(hash) < topicLen {
topicLen = len(hash)
}
var topic [4]byte
for i = 0; i < topicLen; i++ {
topic[i] = hash[i]
}
To summarize, following is the process for peer B to establish a session with peer A:
- Listen to peer B’s Contact Code Topic to retrieve their bundle information, including a list of active devices
- Peer A sends their pre-key bundle on peer B’s partitioned topic
- Peer A and peer B perform the key-exchange using the shared pre-key bundles
- The negotiated topic is derived from the shared secret
- Peers A & B exchange messages on the negotiated topic
Concurrent sessions #
If a node creates two sessions concurrently between two peers, the one with the symmetric key first in byte order SHOULD be used, this marks that the other has expired.
Re-keying #
On receiving a bundle from a given peer with a higher version, the old bundle SHOULD be marked as expired and a new session SHOULD be established on the next message sent.
Multi-device support #
Multi-device support is quite challenging as there is not a central place where information on which and how many devices (identified by their respective installation-id
) a peer has, is stored.
Furthermore, account recovery always needs to be taken into consideration, where a user wipes clean the whole device and the node loses all the information about any previous sessions. Taking these considerations into account, the way the network propagates multi-device information using X3DH bundles, which will contain information about paired devices as well as information about the sending device. This means that every time a new device is paired, the bundle needs to be updated and propagated with the new information, the user has the responsibility to make sure the pairing is successful.
The method is loosely based on Signal’s Sesame Algorithm.
Pairing #
A new installation-id
MUST be generated on a per-device basis.
The device should be paired as soon as possible if other devices are present.
If a bundle is received, which has the same IK
as the keypair present on the device, the devices MAY be paired.
Once a user enables a new device, a new bundle MUST be generated which includes pairing information.
The bundle MUST be propagated to contacts through the usual channels.
Removal of paired devices is a manual step that needs to be applied on each device, and consist simply in disabling the device, at which point pairing information will not be propagated anymore.
Sending messages to a paired group #
When sending a message, the peer SHOULD send a message to other installation-id
that they have seen.
The node caps the number of devices to n
, ordered by last activity.
The node sends messages using pairwise encryption, including their own devices.
Where n
is the maximum number of devices that can be paired.
Account recovery #
Account recovery is the same as adding a new device, and it MUST be handled the same way.
Partitioned devices #
In some cases (i.e. account recovery when no other pairing device is available, device not paired), it is possible that a device will receive a message that is not targeted to its own installation-id
.
In this case an empty message containing bundle information MUST be sent back, which will notify the receiving end not to include the device in any further communication.
Security Considerations #
- Inherits all security considerations from 53/WAKU2-X3DH.
Recommendations #
- The value of
n
SHOULD be configured by the app-protocol.- The default value SHOULD be 3, since a larger number of devices will result in a larger bundle size, which may not be desirable in a peer-to-peer network.
Copyright #
Copyright and related rights waived via CC0.