Currently replies to messages are handled in status-react.
This causes some issues with the fact that sometimes replies might come
out of order, they might be offloaded to the database etc.
This commit changes the behavior so that status-go always returns the
replies, and in case a reply comes out of order (first the reply, later
the message being replied to), it will include in the messages the
updated message.
It also adds some fields (RTL,Replace,LineCount) to the database which
were not previously saved, resulting in some potential bugs.
The method that we use to pull replies is currently a bit naive, we just
pull all the message again from the database, but has the advantage of
being simple. It will go through performance testing to make sure
performnace are acceptable, if so I think it's reasonable to avoid some
complexity.
* Add status-option code
This commits changes the behavior of waku introducing a new status-code,
`2`, that replaces the current single options codes.
* linting
*** How it worked before this PR on multiaccount creation:
- On multiacc creation we scanned chain for eth and erc20 transfers. For
each address of a new empty multiaccount this scan required
1. two `eth_getBalance` requests to find out that there is no any
balance change between zero and the last block, for eth transfers
2. and `chain-size/100000` (currently ~100) `eth_getLogs` requests,
for erc20 transfers
- For some reason we scanned an address of the chat account as well, and
also accounts were not deduplicated. So even for an empty multiacc we
scanned chain twice for each chat and main wallet addresses, in result
app had to execute about 400 requests.
- As mentioned above, `eth_getBalance` requests were used to check if
there were any eth transfers, and that caused empty history in case
if user already used all available eth (so that both zero and latest
blocks show 0 eth for an address). There might have been transactions
but we wouldn't fetch/show them.
- There was no upper limit for the number of rpc requests during the
scan, so it could require indefinite number of requests; the scanning
algorithm was written so that we persisted the whole history of
transactions or tried to scan form the beginning again in case of
failure, giving up only after 10 minutes of failures. In result
addresses with sufficient number of transactions would never be fully
scanned and during these 10 minutes app could use gigabytes of
internet data.
- Failures were caused by `eth_getBlockByNumber`/`eth_getBlockByHash`
requests. These requests return significantly bigger responses than
`eth_getBalance`/`eth_transactionsCount` and it is likely that
execution of thousands of them in parallel caused failures for
accounts with hundreds of transactions. Even for an account with 12k
we could successfully determine blocks with transaction in a few
minutes using `eth_getBalance` requests, but `eth_getBlock...`
couldn't be processed for this acc.
- There was no caching for for `eth_getBalance` requests, and this
caused in average 3-4 times more such requests than is needed.
*** How it works now on multiaccount creation:
- On multiacc creation we scan chain for last ~30 eth transactions and
then check erc20 in the range where these eth transactions were found.
For an empty address in multiacc this means:
1. two `eth_getBalance` transactions to determine that there was no
balance change between zero and the last block; two
`eth_transactionsCount` requests to determine there are no outgoing
transactions for this address; total 4 requests for eth transfers
2. 20 `eth_getLogs` for erc20 transfers. This number can be lowered,
but that's not a big deal
- Deduplication of addresses is added and also we don't scan chat
account, so a new multiacc requires ~25 (we also request latest block
number and probably execute a few other calls) request to determine
that multiacc is empty (comparing to ~400 before)
- In case if address contains transactions we:
1. determine the range which contains 20-25 outgoing eth/erc20
transactions. This usually requires up to 10 `eth_transactionCount`
requests
2. then we scan chain for eth transfers using `eth_getBalance` and
`eth_transactionCount` (for double checking zero balances)
3. we make sure that we do not scan db for more than 30 blocks with
transfers. That's important for accounts with mostly incoming
transactions, because the range found on the first step might
contain any number of incoming transfers, but only 20-25 outgoing
transactions
4. when we found ~30 blocks in a given range, we update initial
range `from` block using the oldest found block
5. and now we scan db for erc20transfers using `eth_getLogs`
`oldest-found-eth-block`-`latest-block`, we make not more than 20 calls
6. when all blocks which contain incoming/outgoing transfers for a
given address are found, we save these blocks to db and mark that
transfers from these blocks are still to be fetched
7. Then we select latest ~30 (the number can be adjusted) blocks from
these which were found and fetch transfers, this requires 3-4
requests per transfer.
8. we persist scanned range so that we know were to start next time
9. we dispatch an event which tells client that transactions are found
10. client fetches latest 20 transfers
- when user presses "fetch more" button we check if app's db contains next
20 transfers, if not we scan chain again and return transfers after
small fixes
Move settings table schema from a key-value store to a one row table with many columns.
We now save the first row with initial data in saveAccountAndLogin and follow up saveSetting calls are only saving one setting at a time.
Co-authored-by: Adam Babik <a.babik@designfortress.com>
* Use a single Message type `v1/message.go` and `message.go` are the same now, and they embed `protobuf.ChatMessage`
* Use `SendChatMessage` for sending chat messages, this is basically the old `Send` but a bit more flexible so we can send different message types (stickers,commands), and not just text.
* Remove dedup from services/shhext. Because now we process in status-protocol, dedup makes less sense, as those messages are going to be processed anyway, so removing for now, we can re-evaluate if bringing it to status-go or not.
* Change the various retrieveX method to a single one:
`RetrieveAll` will be processing those messages that it can process (Currently only `Message`), and return the rest in `RawMessages` (still transit). The format for the response is:
`Chats`: -> The chats updated by receiving the message
`Messages`: -> The messages retrieved (already matched to a chat)
`Contacts`: -> The contacts updated by the messages
`RawMessages` -> Anything else that can't be parsed, eventually as we move everything to status-protocol-go this will go away.
Wallet database refactored so that every query ensures isolation by the network id.
Network id provided when database object is created, thus it is transparent to other parts
of the wallet module.
Additionally every uniqueness index is changed to ensure that it doesn't prevent adding
object with same id but from a different network.
Samuel Hawksby-Robinson
Jonathan Rainville
Gheorghe Pinzaru
Volodymyr Kozieiev
Andrea Maria Piana
andrey
RichΛrd
Roman Volosovskyi
Adam Babik
Pedro Pombeiro
yenda
André Medeiros
Dmitry