*** How it worked before this PR on multiaccount creation:
- On multiacc creation we scanned chain for eth and erc20 transfers. For
each address of a new empty multiaccount this scan required
1. two `eth_getBalance` requests to find out that there is no any
balance change between zero and the last block, for eth transfers
2. and `chain-size/100000` (currently ~100) `eth_getLogs` requests,
for erc20 transfers
- For some reason we scanned an address of the chat account as well, and
also accounts were not deduplicated. So even for an empty multiacc we
scanned chain twice for each chat and main wallet addresses, in result
app had to execute about 400 requests.
- As mentioned above, `eth_getBalance` requests were used to check if
there were any eth transfers, and that caused empty history in case
if user already used all available eth (so that both zero and latest
blocks show 0 eth for an address). There might have been transactions
but we wouldn't fetch/show them.
- There was no upper limit for the number of rpc requests during the
scan, so it could require indefinite number of requests; the scanning
algorithm was written so that we persisted the whole history of
transactions or tried to scan form the beginning again in case of
failure, giving up only after 10 minutes of failures. In result
addresses with sufficient number of transactions would never be fully
scanned and during these 10 minutes app could use gigabytes of
internet data.
- Failures were caused by `eth_getBlockByNumber`/`eth_getBlockByHash`
requests. These requests return significantly bigger responses than
`eth_getBalance`/`eth_transactionsCount` and it is likely that
execution of thousands of them in parallel caused failures for
accounts with hundreds of transactions. Even for an account with 12k
we could successfully determine blocks with transaction in a few
minutes using `eth_getBalance` requests, but `eth_getBlock...`
couldn't be processed for this acc.
- There was no caching for for `eth_getBalance` requests, and this
caused in average 3-4 times more such requests than is needed.
*** How it works now on multiaccount creation:
- On multiacc creation we scan chain for last ~30 eth transactions and
then check erc20 in the range where these eth transactions were found.
For an empty address in multiacc this means:
1. two `eth_getBalance` transactions to determine that there was no
balance change between zero and the last block; two
`eth_transactionsCount` requests to determine there are no outgoing
transactions for this address; total 4 requests for eth transfers
2. 20 `eth_getLogs` for erc20 transfers. This number can be lowered,
but that's not a big deal
- Deduplication of addresses is added and also we don't scan chat
account, so a new multiacc requires ~25 (we also request latest block
number and probably execute a few other calls) request to determine
that multiacc is empty (comparing to ~400 before)
- In case if address contains transactions we:
1. determine the range which contains 20-25 outgoing eth/erc20
transactions. This usually requires up to 10 `eth_transactionCount`
requests
2. then we scan chain for eth transfers using `eth_getBalance` and
`eth_transactionCount` (for double checking zero balances)
3. we make sure that we do not scan db for more than 30 blocks with
transfers. That's important for accounts with mostly incoming
transactions, because the range found on the first step might
contain any number of incoming transfers, but only 20-25 outgoing
transactions
4. when we found ~30 blocks in a given range, we update initial
range `from` block using the oldest found block
5. and now we scan db for erc20transfers using `eth_getLogs`
`oldest-found-eth-block`-`latest-block`, we make not more than 20 calls
6. when all blocks which contain incoming/outgoing transfers for a
given address are found, we save these blocks to db and mark that
transfers from these blocks are still to be fetched
7. Then we select latest ~30 (the number can be adjusted) blocks from
these which were found and fetch transfers, this requires 3-4
requests per transfer.
8. we persist scanned range so that we know were to start next time
9. we dispatch an event which tells client that transactions are found
10. client fetches latest 20 transfers
- when user presses "fetch more" button we check if app's db contains next
20 transfers, if not we scan chain again and return transfers after
small fixes
Move settings table schema from a key-value store to a one row table with many columns.
We now save the first row with initial data in saveAccountAndLogin and follow up saveSetting calls are only saving one setting at a time.
Co-authored-by: Adam Babik <a.babik@designfortress.com>
Account's address was used as a primary key in accounts db and as a
deterministic id of an account in some API calls. Also it was used as a
part of the name of the account specific database. This revealed some
extra information about the account and wasn't necessary.
At first the hash of the address was planned to be used as a
deterministic id, but we already have a keyUid which is calculated as
sha256 hash of account's public key and has similar properties:
- it is deterministic
- doesn't reveal accounts public key or address in plain
* WIP accounts implementation
* Accounts datasore and changes to status mobile API
* Add library changes and method to update config
* Handle error after account selection
* Add two methods to start account to backend
* Use encrypted database for settings and add a service for them
* Resolve linter warning
* Bring back StartNode StopNode for tests
* Add sub accounts and get/save api
* Changes to accounts structure
* Login use root address and fetch necessary info from database
* Cover accounts store with tests
* Refactor in progress
* Initialize status keystore instance before starting ethereum node
* Rework library tests
* Resolve failures in private api test and send transaction test
* Pass pointer to initialized config to unmarshal
* Use multiaccounts/accounts naming consistently
Multiaccount is used as a login identifier
Account references an address and a key, if account is not watch-only.
* Add login timestamp stored in the database to accounts.Account object
* Add photo-path field for multiaccount struct
* Add multiaccoutns rpc with updateAccount method
Update to any other account that wasn't used for login will return an error
* Fix linter in services/accounts
* Select account before starting a node
* Save list of accounts on first login
* Pass account manager to accounts service to avoid selecting account before starting a node
* Add logs to login with save and regualr login
* multi-account login and signing
put methods count threshold back to 20
* validate login params
* refactoring
* use common.Address
* remove unused var in test
* Store tx and receipt in db and cast it to TransferView on read
* Store Log instead of log index
* Use contract from log and bring back address field
* Add tx status and id fields
[services/wallet] Several changes in API after feedback
- Timestamp from block header stored in blocks table and added to each transfers
- From field is computed from signature to offload this computation from client side
- `history` event is added back, so that client can ignore historical blocks when watching
only for new blocks
- block number and timestamp are marshalled in hex. consistent with ethereum data structures
* Implement subscriptions and filtering
* Add e2e test with log filter polling logs from EVM with clique backend
* Apply review comments
* Move devnode to t/devtests to avoid cycle in imports
Andrea Maria Piana
Roman Volosovskyi
Pedro Pombeiro
yenda
Adam Babik
Dmitry
Andrea Franz
Ivan Daniluk