- Fix two possible RangeErrors, due to negative seq allocation
in decodeAuthMessageEIP8 and in decodeAckMessageEIP8
- Set the minimum auth message size to AuthMessageEIP8Length,
in case there are clients that no longer add padding
- Add tests for invalid length cases
RLP Enum deserialization would currently not check if "hole values"
were attempted to be converted to the enum type. Now use
checkedEnumAssign and fail with RlpTypeMismatch on invalid values.
There is at least one occurance of an enum with holes in rlpx p2p:
DisconnectionReason. For this enum the issue could occur.
Also:
- Added enum RLP tests and rlpx p2p disconnect message tests to
test the DisconnectionReason with enum hole value.
- Fixed worse custom DisconnectionReason decoding occurance
in rlpx in waitSingleMsg proc where this issue could occur.
Nim devel brach(1.7.1) introduce gc=orc as default mode.
Because the p2p protocol using unsafe pointer operations
for it's ProtocolInfo and using global variables scattered
around, the orc mistakenly(or maybe correctly) crash the protocol.
* Provide dedicated `DisconnectionReason` enum type RLP reader
why:
Without this reader, the program communicating via RLPX will crash when
receiving out of bound reason codes disconnect message.
Out of bound value assignments to an enum causes a `RangeError`defect
and consequently the program to terminate. This `RangeError` is avoided
here and a `MalformedRlpError` catchable error raised.
* Using default exception type in bespoke `read(DisconnectionReason)`
why:
This should not differ from the default enum parser. The particular
message is different and more targeted, here.
Note: The default RLP parser was not used because `
`array[1,DisconnectionReason]` is currently not properly handled and
should give a siliar error message as a `DisconnectionReason` error.
* De-clutter, custom read() was not needed
Co-authored-by: jordan <jordan@curd.mjh-it.com>
* Handle the decodeAuthMessage error case separatly and log to trace
Garbage data on the TCP port (e.g. from port scanners) would
cause lots of error log messages, so log this to trace and get rid
of a (little) bit of exception usage in the process.
* Remove usage of result var in rlpxAccept and rlpxConnect
* Discv4: Add ENRRequest & ENRResponse msgs to avoid fails on these
Fix#499
These messages are not implemented yet however, but just ignored.
why:
Rlp errors throw exceptions which cause the dispatcher loop to
terminate the current session immediately.
details:
The DisconnectionReasonList message requires a single entry list.
Observed and now accepted deviations are:
Geth: single byte number
bor(a Geth fork): blobbed single entry list containing a number
The ENR code used to be solely exception based, and these
exceptions where a left-over of that. They are useless as later
calls use Result anyhow.
Additionally, they cause quite the performance loss because they
are used in the "common path" for the toTypedRecord call, e.g.
when reading the fields of ip6, tcp6 and udp6.
Currently only setting `--styleCheck:hint` as there are some
dependency fixes required and the compiler seems to trip over the
findnode MessageKind, findnode Message field and the findNode
proc. Also over protocol.Protocol usage.
toBytes for NodeId wasn't selected by compiler byt if it does
get selected, it will fail on the test cases due to the
countdown that is done in logDistance.
Set to toBytesBE properly now and do countup, that should make
it correct also for BE architecture.
Removed toBytes to avoid confusion and avoid this one being
selected ever. The only place toBytes for NodeId was used is in
sessions.nim makeKey func and there also the stint one
(thus native endianness) was selected in Nim 1.2.x.
Native endianness is fine there as it is only an internal
representation.
* Don't fail ENR decoding when value is an RLP list
* Store RLP raw list in the ENR field pair instead
* Add ENR kList FieldKind so lists can be treated differently
Treated differently now when printing out the ENR, mentioning
that it is a raw RLP list
* Allow for tcp/udp ports to always be configured
- Allow for an ENR to be build with tcp and udp ports also when
no IP address is provided
- In the address set-up always provide best efforttcp and udp ports
also when configuration of external ip (and/or ports) fails.
* Modify nodes verification
* Move nodes verification to separate module
By moving verification to separate module it can be re-used
in different contexts not only in discoveryv5.
Kim De Mey
Justin Traglia
andri lim
Jacek Sieka
KonradStaniec
tersec
oskarth
Jordan Hrycaj
Jordan Hrycaj
Etan Kissling
Ștefan Talpalaru