Co-authored-by: R.B. Boyer <4903+rboyer@users.noreply.github.com>
Previously we would associate the address of a discovery chain target
with the discovery chain's filter chain. This was broken for a few reasons:
- If the upstream is a virtual service, the client proxy has no way of
dialing it because virtual services are not targets of their discovery
chains. The targets are distinct services. This is addressed by watching
the endpoints of all upstream services, not just their discovery chain
targets.
- If multiple discovery chains resolve to the same target, that would
lead to multiple filter chains attempting to match on the target's
virtual IP. This is addressed by only matching on the upstream's virtual
IP.
NOTE: this implementation requires an intention to the redirecting
virtual service and not just to the final destination. This is how
we can know that the virtual service is an upstream to watch.
A later PR will look into traversing discovery chains when computing
upstreams so that intentions are only required to the discovery chain
targets.
No config entry needs a Kind field. It is only used to determine the Go type to
target. As we introduce new config entries (like this one) we can remove the kind field
and have the GetKind method return the single supported value.
In this case (similar to proxy-defaults) the Name field is also unnecessary. We always
use the same value. So we can omit the name field entirely.
This adds support for the Incremental xDS protocol when using xDS v3. This is best reviewed commit-by-commit and will not be squashed when merged.
Union of all commit messages follows to give an overarching summary:
xds: exclusively support incremental xDS when using xDS v3
Attempts to use SoTW via v3 will fail, much like attempts to use incremental via v2 will fail.
Work around a strange older envoy behavior involving empty CDS responses over incremental xDS.
xds: various cleanups and refactors that don't strictly concern the addition of incremental xDS support
Dissolve the connectionInfo struct in favor of per-connection ResourceGenerators instead.
Do a better job of ensuring the xds code uses a well configured logger that accurately describes the connected client.
xds: pull out checkStreamACLs method in advance of a later commit
xds: rewrite SoTW xDS protocol tests to use protobufs rather than hand-rolled json strings
In the test we very lightly reuse some of the more boring protobuf construction helper code that is also technically under test. The important thing of the protocol tests is testing the protocol. The actual inputs and outputs are largely already handled by the xds golden output tests now so these protocol tests don't have to do double-duty.
This also updates the SoTW protocol test to exclusively use xDS v2 which is the only variant of SoTW that will be supported in Consul 1.10.
xds: default xds.Server.AuthCheckFrequency at use-time instead of construction-time
This config entry is being renamed primarily because in k8s the name
cluster could be confusing given that the config entry applies across
federated datacenters.
Additionally, this config entry will only apply to Consul as a service
mesh, so the more generic "cluster" name is not needed.
Setting this field to a value is equivalent to using the 'near' query paramter.
The intent is to sort the results by proximity to the node requesting
them. However with connect we send the results to envoy, which doesn't
care about the order, so setting this field is increasing the work
performed for no gain.
It is necessary to unset this field now because we would like connect
to use streaming, but streaming does not support sorting by proximity.
This PR replaces the original boolean used to configure transparent
proxy mode. It was replaced with a string mode that can be set to:
- "": Empty string is the default for when the setting should be
defaulted from other configuration like config entries.
- "direct": Direct mode is how applications originally opted into the
mesh. Proxy listeners need to be dialed directly.
- "transparent": Transparent mode enables configuring Envoy as a
transparent proxy. Traffic must be captured and redirected to the
inbound and outbound listeners.
This PR also adds a struct for transparent proxy specific configuration.
Initially this is not stored as a pointer. Will revisit that decision
before GA.
Deadlock scenario:
1. Due to scheduling, the state runner sends one snapshot into
snapCh and then attempts to send a second. The first send succeeds
because the channel is buffered, but the second blocks.
2. Separately, Manager.Watch is called by the xDS server after
getting a discovery request from Envoy. This function acquires the
manager lock and then blocks on receiving the CurrentSnapshot from
the state runner.
3. Separately, there is a Manager goroutine that reads the snapshots
from the channel in step 1. These reads are done to notify proxy
watchers, but they require holding the manager lock. This goroutine
goes to acquire that lock, but can't because it is held by step 2.
Now, the goroutine from step 3 is waiting on the one from step 2 to
release the lock. The goroutine from step 2 won't release the lock until
the goroutine in step 1 advances. But the goroutine in step 1 is waiting
for the one in step 3. Deadlock.
By making this send non-blocking step 1 above can proceed. The coalesce
timer will be reset and a new valid snapshot will be delivered after it
elapses or when one is requested by xDS.
Add a skip condition to all tests slower than 100ms.
This change was made using `gotestsum tool slowest` with data from the
last 3 CI runs of master.
See https://github.com/gotestyourself/gotestsum#finding-and-skipping-slow-tests
With this change:
```
$ time go test -count=1 -short ./agent
ok github.com/hashicorp/consul/agent 0.743s
real 0m4.791s
$ time go test -count=1 -short ./agent/consul
ok github.com/hashicorp/consul/agent/consul 4.229s
real 0m8.769s
```
This implements a solution for #7863
It does:
Add a new config cache.entry_fetch_rate to limit the number of calls/s for a given cache entry, default value = rate.Inf
Add cache.entry_fetch_max_burst size of rate limit (default value = 2)
The new configuration now supports the following syntax for instance to allow 1 query every 3s:
command line HCL: -hcl 'cache = { entry_fetch_rate = 0.333}'
in JSON
{
"cache": {
"entry_fetch_rate": 0.333
}
}
The rationale behind removing them is that all of our own code (xDS, builtin connect proxy) use the cache notification mechanism. This ensures that the blocking fetch behind the scenes is always executing. Therefore the only way you might go to get a certificate and have to wait is when 1) the request has never been made for that cert before or 2) you are using the v1/agent/connect/ca/leaf API for retrieving the cert yourself.
In the first case, the refresh change doesn’t alter the behavior. In the second case, it can be mitigated by using blocking queries with that API which just like normal cache notification mechanism will cause the blocking fetch to be initiated and to get leaf certs as soon as needed.
If you are not using blocking queries, or Envoy/xDS, or the builtin connect proxy but are retrieving the certs yourself then the HTTP endpoint might take a little longer to respond.
This also renames the RefreshTimeout field on the register options to QueryTimeout to more accurately reflect that it is used for any type that supports blocking queries.
And fix the 'value not used' issues.
Many of these are not bugs, but a few are tests not checking errors, and
one appears to be a missed error in non-test code.
Freddy
freddygv
Daniel Nephin
Mark Anderson
R.B. Boyer
freddygv
R.B. Boyer
Matt Keeler
Pierre Souchay