* Add partition fields to targets like service route destinations
* Update validation to prevent cross-DC + cross-partition references
* Handle partitions when reading config entries for disco chain
* Encode partition in compiled targets
* add root_cert_ttl option for consul connect, vault ca providers
Signed-off-by: FFMMM <FFMMM@users.noreply.github.com>
* Apply suggestions from code review
Co-authored-by: Chris S. Kim <ckim@hashicorp.com>
* add changelog, pr feedback
Signed-off-by: FFMMM <FFMMM@users.noreply.github.com>
* Update .changelog/11428.txt, more docs
Co-authored-by: Daniel Nephin <dnephin@hashicorp.com>
* Update website/content/docs/agent/options.mdx
Co-authored-by: Kyle Havlovitz <kylehav@gmail.com>
Co-authored-by: Chris S. Kim <ckim@hashicorp.com>
Co-authored-by: Daniel Nephin <dnephin@hashicorp.com>
Co-authored-by: Kyle Havlovitz <kylehav@gmail.com>
This struct allows us to move all the deprecated config options off of
the main config struct, and keeps all the deprecation logic in a single
place, instead of spread across 3+ places.
Signed-off-by: Jakub Sokołowski <jakub@status.im>
* agent: add failures_before_warning setting
The new setting allows users to specify the number of check failures
that have to happen before a service status us updated to be `warning`.
This allows for more visibility for detected issues without creating
alerts and pinging administrators. Unlike the previous behavior, which
caused the service status to not update until it reached the configured
`failures_before_critical` setting, now Consul updates the Web UI view
with the `warning` state and the output of the service check when
`failures_before_warning` is breached.
The default value of `FailuresBeforeWarning` is the same as the value of
`FailuresBeforeCritical`, which allows for retaining the previous default
behavior of not triggering a warning.
When `FailuresBeforeWarning` is set to a value higher than that of
`FailuresBeforeCritical it has no effect as `FailuresBeforeCritical`
takes precedence.
Resolves: https://github.com/hashicorp/consul/issues/10680
Signed-off-by: Jakub Sokołowski <jakub@status.im>
Co-authored-by: Jakub Sokołowski <jakub@status.im>
This field was never user-configurable. We always overwrote the value with 120s from
NonUserSource. However, we also never copied the value from RuntimeConfig to consul.Config,
So the value in NonUserSource was always ignored, and we used the default value of 30s
set by consul.DefaultConfig.
All of this code is an unnecessary distraction because a user can not actually configure
this value.
This commit removes the fields and uses a constant value instad. Someone attempting to set
acl.disabled_ttl in their config will now get an error about an unknown field, but previously
the value was completely ignored, so the new behaviour seems more correct.
We have to keep this field in the AutoConfig response for backwards compatibility, but the value
will be ignored by the client, so it doesn't really matter what value we set.
This field has been unnecessary for a while now. It was always set to the same value
as PrimaryDatacenter. So we can remove the duplicate field and use PrimaryDatacenter
directly.
This change was made by GoLand refactor, which did most of the work for me.
This change adds a new `dns_config.recursor_strategy` option which
controls how Consul queries DNS resolvers listed in the `recursors`
config option. The supported options are `sequential` (default), and
`random`.
Closes#8807
Co-authored-by: Blake Covarrubias <blake@covarrubi.as>
Co-authored-by: Priyanka Sengupta <psengupta@flatiron.com>
And remove BuildAndValidate. This commit completes some earlier work to reduce the config
interface a single Load function.
The last remaining test was converted to use Load instad of BuildAndValidate.
The hcl decoding apparently uses strconv.ParseInt, which fails to parse a 64bit int.
Since hcl v1 is basically EOl, it seems unlikely we'll fix this in hcl.
Since this test is only about loading values from config files, the extra large number
doesn't seem important. Trim a few zeros from the numbers so that they parse
properly on 32bit platforms.
Also skip a slow test when -short is used.
CatalogDestinationsOnly is a passthrough that would enable dialing
addresses outside of Consul's catalog. However, when this flag is set to
true only _connect_ endpoints for services can be dialed.
This flag is being renamed to signal that non-Connect endpoints can't be
dialed by transparent proxies when the value is set to true.
No config entry needs a Kind field. It is only used to determine the Go type to
target. As we introduce new config entries (like this one) we can remove the kind field
and have the GetKind method return the single supported value.
In this case (similar to proxy-defaults) the Name field is also unnecessary. We always
use the same value. So we can omit the name field entirely.
This config entry is being renamed primarily because in k8s the name
cluster could be confusing given that the config entry applies across
federated datacenters.
Additionally, this config entry will only apply to Consul as a service
mesh, so the more generic "cluster" name is not needed.
This PR replaces the original boolean used to configure transparent
proxy mode. It was replaced with a string mode that can be set to:
- "": Empty string is the default for when the setting should be
defaulted from other configuration like config entries.
- "direct": Direct mode is how applications originally opted into the
mesh. Proxy listeners need to be dialed directly.
- "transparent": Transparent mode enables configuring Envoy as a
transparent proxy. Traffic must be captured and redirected to the
inbound and outbound listeners.
This PR also adds a struct for transparent proxy specific configuration.
Initially this is not stored as a pointer. Will revisit that decision
before GA.
* add http2 ping checks
* fix test issue
* add h2ping check to config resources
* add new test and docs for h2ping
* fix grammatical inconsistency in H2PING documentation
* resolve rebase conflicts, add test for h2ping tls verification failure
* api documentation for h2ping
* update test config data with H2PING
* add H2PING to protocol buffers and update changelog
* fix typo in changelog entry
Some TLS servers require SNI, but the Golang HTTP client doesn't
include it in the ClientHello when connecting to an IP address. This
change adds a new TLSServerName field to health check definitions to
optionally set it. This fixes#9473.
Eric
FFMMM
Dan Upton
freddygv
Daniel Nephin
tarat44
R.B. Boyer
Dhia Ayachi
Chris S. Kim
Blake Covarrubias
Freddy
Mark Anderson
freddygv
Christopher Broglie